OPERATOR’S MANUALSNOW THROWERMODELSnow Boss 750TPRINTED IN U.S.A.IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWHITE OUTDOOR PRODUCTS COMPANY
10To Engage Track Drive• With the engine running near top speed, move the shift lever into one of the six FORWARD positions or two REVERSE positions.
11Chute Directional Control And Support Bracket AdjustmentIf the spiral at the base of the chute directional control is not fully engaging with the no
12Drive and Shifting MechanismLubricate at least once a season or after every 25 hours of operation. Remove the rear cover, lubricate any chains, spro
13IMPORTANT:NEVER replace the auger shear bolts with standard hex bolts. Any damage to the auger gearbox or other components as a result of doing so w
14NOTE: The support bracket must rest on the stop boltafter the new belt has been assembled.Figure 16Servicing Friction Wheel RubberThe rubber on the
15WARNING: Never store the machine orfuel container indoors where there is anopen flame, spark, or pilot light such as onwater heater, furnace, clothe
16SECTION 8: TROUBLESHOOTINGProblem Cause RemedyEngine fails to start 1. Fuel tank empty, or stale fuel.2. Blocked fuel line.3. Choke not in the ON p
17Model 750TRef. No.Part No. Part Description1. 618-0123 RH Housing2. 618-0418 LH Housing w/Fitting3. 710-0642 Self Tapping Screw, 1/4-20 x .754. 711-
18Model 750T923292412628187122062115AA541811271220443532484535323344454649327236385132114243434211694731403437BB54625566595363645955656045452615556578
19Model 750TRef. No.Part No. Part Description1. 684-0008A Shift Arm Assembly2. 705-5204A Chute Crank Ass’y4. 710-0262 Carriage Bolt, 5/16-18 x 1.55.
2TABLE OF CONTENTSContent PageImportant Safe Operation Practices...3Assembling Your Sn
20Model 750T1234567891011121415131610212223252322261827281330313233161835343637383941404217403929242091918164344
21Model 750TRef. No.Part No. Part Description1. 712-0116 Lock Jam Nut 3/8-242. 756-0178 Flat Idler 3. 784-5632A Auger Idler Arm4. 710-0459A Hex Cap Sc
22Model 750T1123456748910111213141516171819191616162021222324252627282930
23Models 750TRef. No.Part No. Part Description1. 710-1652 Hex Washer Screw 1/4-20 x .6252. 731-1324 Belt Cover3. 732-0710 Extension Spring4. 710-0627
2425192627242322211617181920293031232323430227261925362124232212 230101819202113111415937654324039383237Models 750T28835
25NOTE: For painted parts, please refer to the listof color codes below. Please add the applicablecolor code, wherever needed, to the part numberto or
26Models 750T12631012785491315141716192022222019282118211815131429313230323437383623352739114041424443455146474852465351545554501617493756562425262633
27Models 750TRef. No.Part No. Part Description1. 720-0223 Grip2. 710-0604 Tap Screw, 5/16-18 x .6253. 784-5642 Track Lockout Plate4. 710-0157 Hex Cap
MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by White Out-door Products Co. with respect to new merchandise pur-c
3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: This symbol points out important safety instructions which, if not followed, could endanger th
43. The clutch levers must operate easily in both directions and automatically return to the disengaged position when released. 4. Never operate with
5SECTION 2: ASSEMBLING YOUR SNOW THROWERNOTE: Any reference in this manual to the left or rightside of the snow thrower is observed from theoperator’
6• Plug the wire from the headlight into the wire lead coming from the right side of the engine, beneath the fuel tank.Final AdjustmentsAuger Control
7If the machine can be moved freely both forward and rearward when the traction control fully depressed, proceed as follows:• Loosen the jam nut on th
8HeadlightThe headlight is on whenever the engine is running.Shift Lever The shift lever is located in the center of the handle panel and is used to d
9• A plastic cup is provided inside the fuel fill opening on the fuel tank. Remove and discard this cup before filling up the tank. Use the separate f
Kommentare zu diesen Handbüchern